How to replace the hydraulic hoses in a hydraulic wheel loader?

Jan 16, 2026

Leave a message

David Miller
David Miller
David is a quality control engineer at Ruyi Hengye. He meticulously inspects all incoming engineering machinery and logistics equipment to ensure they meet the strict international standards set by the company and the industry.

Hydraulic wheel loaders are essential pieces of equipment in construction, mining, and various other industries. The hydraulic hoses in these machines play a crucial role in transmitting hydraulic fluid to power different components such as the lift arms, bucket, and steering. Over time, these hoses can wear out, develop leaks, or get damaged, which requires timely replacement to ensure the proper functioning of the loader. As a hydraulic wheel loader supplier, I will guide you through the process of replacing hydraulic hoses in a hydraulic wheel loader.

Step 1: Preparation

Before you start replacing the hydraulic hoses, it is essential to gather all the necessary tools and materials. You will need a set of wrenches, a socket set, a hydraulic hose cutter, a deburring tool, a torque wrench, and replacement hoses that are compatible with your loader model. It is also a good idea to have a container to collect any spilled hydraulic fluid and some rags to clean up.

Make sure to refer to the loader's manual for specific instructions and safety precautions. Different models may have slightly different procedures, and it is important to follow the manufacturer's guidelines.

Step 2: Safety First

Safety should always be your top priority when working on a hydraulic wheel loader. First, park the loader on a level surface and engage the parking brake. Turn off the engine and allow the hydraulic system to cool down completely. This will prevent any accidental activation of the hydraulic components and reduce the risk of burns from hot hydraulic fluid.

90-25-Type Small Wheel Loader high quality953-Type Small Wheel Loader factory

Wear appropriate personal protective equipment (PPE), including safety glasses, gloves, and protective clothing. Hydraulic fluid can be harmful if it comes into contact with your skin or eyes, so take all necessary precautions.

Step 3: Identify the Faulty Hose

Inspect the hydraulic hoses carefully to identify the one that needs to be replaced. Look for signs of wear, such as cracks, bulges, or leaks. Pay special attention to the connections and areas where the hoses are exposed to high stress or friction. If you are unsure which hose is faulty, you can use a pressure gauge to check the pressure in different parts of the hydraulic system.

Step 4: Relieve the Hydraulic Pressure

Before you remove the faulty hose, you need to relieve the hydraulic pressure in the system. Locate the pressure relief valve, which is usually marked on the hydraulic manifold. Use a wrench to slowly open the valve and release the pressure. You will hear a hissing sound as the pressure is released. Make sure to do this slowly to avoid any sudden release of fluid.

Step 5: Remove the Faulty Hose

Once the pressure is relieved, use the appropriate wrenches to loosen the fittings at both ends of the faulty hose. Be careful not to damage the fittings or the surrounding components. Place the container under the hose to collect any remaining hydraulic fluid. Gently pull the hose out of the fittings and set it aside.

Step 6: Prepare the New Hose

Take the new hose and measure it to ensure it is the correct length. Use the hydraulic hose cutter to cut the hose to the appropriate length. Make sure to cut the hose straight and cleanly. Use the deburring tool to remove any burrs or sharp edges from the cut ends of the hose.

Step 7: Install the New Hose

Insert the new hose into the fittings at both ends. Make sure the hose is properly seated and aligned. Use the wrenches to tighten the fittings securely. However, be careful not to over-tighten the fittings, as this can damage the hose or the fittings. Refer to the loader's manual for the recommended torque values.

Step 8: Refill the Hydraulic Fluid

Once the new hose is installed, you need to refill the hydraulic fluid in the system. Locate the hydraulic fluid reservoir and remove the cap. Use a funnel to pour the recommended type and amount of hydraulic fluid into the reservoir. Check the fluid level using the dipstick or sight glass and make sure it is within the recommended range.

Step 9: Bleed the Hydraulic System

After refilling the hydraulic fluid, you need to bleed the system to remove any air bubbles. Start the engine and let it idle for a few minutes. Slowly operate the hydraulic controls to move the lift arms and bucket up and down a few times. This will help to circulate the fluid and remove any air bubbles. Check the fluid level again and add more if necessary.

Step 10: Test the System

Once you have bled the system, test the hydraulic system to make sure it is working properly. Operate the lift arms, bucket, and steering to check for any leaks or abnormal noises. If everything seems to be working fine, you can consider the hose replacement process complete.

Conclusion

Replacing hydraulic hoses in a hydraulic wheel loader is a relatively straightforward process if you follow the proper steps and take the necessary safety precautions. As a hydraulic wheel loader supplier, we offer a wide range of high-quality hydraulic hoses for different models of wheel loaders, including the 630-Type Small Wheel Loader, 953-Type Small Wheel Loader, and 90-25-Type Small Wheel Loader.

If you have any questions or need further assistance with hose replacement or any other aspect of hydraulic wheel loader maintenance, please feel free to contact us. We are always ready to help you keep your equipment in top condition.

References

  • Manufacturer's manual for the hydraulic wheel loader
  • Hydraulic hose installation and maintenance guidelines
Send Inquiry