The main components of a forklift's valve train include:
Valve: There are two types of valves: intake valves and exhaust valves. Their function is to open and close the intake and exhaust passages. They consist of a head and a stem. The head opens and closes the intake and exhaust passages, while the stem guides the valve's movement. Intake valves are made of ordinary alloy steel, while exhaust valves are made of heat-resistant alloy steel because the exhaust valve head is in direct contact with combustion gases and is subject to significant heat.
To ensure a tight fit and heat conduction between the valve head and valve seat, a tapered mating surface is used between them, and this surface is ground. The angle between the tapered surface and the top plane is called the valve cone angle, commonly 30° and 45°. The valve stem is the guide part for valve movement. Commonly, the valve stem has a groove cut into the tail end for mounting a tapered locking plate.
Valve Seat: The valve seat is a circular seat hole directly machined into the cylinder block (for side-mounted valves) or cover (for top-mounted valves). It mates with the valve to provide a seal. Some valve seats can be machined from wear-resistant alloy cast iron into seat rings and inlaid on the cylinder block or cylinder head.
Valve guide: Its function is to guide the valve to make the correct axial movement, and at the same time, indirectly transfer the heat from the valve stem to the water jacket. For ease of repair and replacement, the valve guide is manufactured separately and then pressed into the cylinder block (or cylinder head). When the valve guide is pressed into the cylinder block (or cylinder head), there should be a certain interference fit and pressing depth to ensure good heat transfer.
Valve spring: Its function is to ensure the tight seal between the valve and the valve seat, and to reduce and overcome the inertial forces generated by the valve and other transmission components to prevent damage to the normal operation of the valve train.
Valve tappet: It transmits the pushing motion of the camshaft to the valve (side-mounted) or pushrod (overhead-mounted) to control the opening and closing of the valve.
Valve pushrod: In an overhead valve train, it transmits the motion of the tappet to the rocker arm. The pushrod is a straight rod made of hollow steel tubing, with different shaped ends welded to both ends. The upper end is a concave spherical shape, where the ball head of the adjusting screw on the rocker arm rests; the lower end is a round ball head for insertion into the concave ball bearing of the pushrod.
The valve rocker arm: Its function is to change the direction of the pushrod's movement and transmit it to the valve. It is a double-arm lever of unequal length with a central hole. The end of the longer arm has an arc-shaped working surface that contacts the valve tail; the end of the shorter arm has a threaded hole for installing the adjusting screw and lock nut to adjust the valve clearance. The middle section houses the rocker arm bearing, which contains a bronze bushing.
The rocker arm shaft: It is a hollow round shaft mounted on the cylinder head with several supports. The rocker arm is fitted onto the rocker arm shaft and can swing in an arc on the shaft. The inner hole of the shaft communicates with the main oil passage, supplying lubricating oil to the valve train.
The camshaft: Used to control the closing time and opening degree of the valves in each cylinder. It also drives the oil pump, fuel pump, distributor, and other accessories. It is a single unit consisting of an intake cam, an exhaust cam, journals, gears that drive the oil pump and distributor, and an eccentric wheel that drives the rocker arm of the fuel pump.
Timing Gears: The camshaft is usually driven by the crankshaft through a pair of timing gears. The pinion is mounted at the front end of the crankshaft and is called the crankshaft timing gear. The large gear is mounted at the front end of the camshaft and is called the camshaft timing gear. The ratio of the pinion to the large gear is 2:1, ensuring that the camshaft rotates one revolution for every two revolutions of the crankshaft.
To ensure correct valve timing and ignition timing, meshing marks are engraved at the corresponding positions of the two gears. To limit the axial movement of the camshaft caused by changes in engine speed during operation, axial limiting devices are provided during installation .
